Bently Nevada 330106-05-30-50-12-05 Proximity Probe

Producto Introduction

The Bently Nevada 330106-05-30-50-12-05 is a proximity probe that supports reliable condition monitoring on rotating machinery. As a genuine Bently Nevada part, it integrates with existing protection loops and is available from TenBN with the official service documentation.

Technical Parameters

• Modelo: 330106-05-30-50-12-05
• Producto Type: Proximity Probe
• Series de Productos: 330105 / 330106
• Origin: U.S.A
• Total length Option: 50 = 5.0 meters (16.4 feet)
• Connector Option: :
• The fluidloc cable Option: –12 is not
• Agency approval Option: 05 = CSA, ATEX, IECEx Approvals
• Probe tip material: Polyphenylene sulfide (PPS)
• Probe case material: AISI 303 or 304 stainless steel (SST)
• Total probe lengths: 0.5, 1, 1.5, 2
• Lengths: 0.5, 1, 1.5, 2, 5, or 9

Parámetro Analysis

Configuration of the 330106-05-30-50-12-05 is carried entirely in its part number, which makes the full string the reference point for spare parts planning and system design. The total length Option specifies 50 = 5.0 meters (16.4 feet). The connector Option specifies :. The the fluidloc cable Option specifies –12 is not. The unit is rated for operation from -52°C to +177°C (-62°F to +350°F). Compliance documentation covers cSA, ATEX, IECEx Approvals.

Probe performance is specified together with the matching extension cable and Proximitor, so replacing the complete loop under consistent part numbers preserves the calibrated scale factor and linearity of the measurement chain.

Aplicación Scenarios

This probe is installed on steam and gas turbines, compressors, pumps, motors, and fans to measure radial and axial shaft vibration, position, and speed. It feeds the associated monitoring rack, giving operators the early warning needed to plan maintenance before a developing fault becomes unplanned downtime.

Installation Guide

Thread the probe into its tapped hole, respect the thread engagement limits of the case, and mate the connector to the matching extension cable. Set the initial gap according to the electrical requirements of the associated Proximitor and verify the gap voltage against system documentation before returning the machine to service.

Compatibility

This component belongs to the 3300 XL 8 mm proximity system and is engineered to work with the associated probes, extension cables, Proximitors, and monitoring hardware of the same system. Bently Nevada components sharing the same part number are fully interchangeable, so a stocked spare can be fitted without re-engineering the measurement loop. TenBN can supply the complete chain under consistent part numbers.

Maintenance Advice

Inspect the probe tip, threads, and cable jacket at each outage for wear or damage, and confirm connector seating and torque have not relaxed in service. Keep the unit within its -52°C to +177°C (-62°F to +350°F) operating envelope in service and storage.

Procurement Advice

Confirm the complete part number against your machine’s bill of materials before ordering, since each option digit changes the mechanical or electrical fit. TenBN stocks genuine Bently Nevada components and provides the official service documentation for this model. For inventory, pricing, and lead time on the 330106-05-30-50-12-05, contact [email protected].

Frequently Asked Questions

What is the operating temperature range?

The unit is rated from -52°C to +177°C (-62°F to +350°F), covering the temperature extremes typical of turbomachinery installations.

What approvals or certifications does it carry?

Compliance documentation covers cSA, ATEX, IECEx Approvals. Confirm the approval suffix on your part number before ordering for hazardous-area use.

Can this spare be interchanged with existing components?

Bently Nevada components sharing the same part number are fully interchangeable, so this spare can replace an existing unit without recalibrating the loop when the complete part number matches.

How do I confirm the right part number?

Check every option digit against the machine bill of materials, then contact [email protected] with the full string; the TenBN team will confirm fit, stock, and documentation.